Neue Variablen:
keine
Obsolete Variablen:
config/dsl.txt:
PPPOE_SYNCHRONOUS
Neue Variablen:
keine
Obsolete Variablen:
keine
Neue Variablen:
config/dsl.txt:
PPTP_NAME='DSL' # circuit name, don't write spaces
PPTP_USEPEERDNS='no' # use dns server of your provider: yes or no
PPTP_CHARGEINT='60' # value of charge interval (in seconds)
PPTP_TIMES='Mo-Su:00-24:0.0:Y' # times/charges when LCR
Neue Variablen:
OPT_HDTUNE='no' # power down HD after some time
HDTUNE_N='1' # number of drives to set sleep-mode
HDTUNE_DISK_1='hda' # drive to handle
HDTUNE_SLEEP_1='yes' # sleep mode: yes or no
HDTUNE_SLEEPTIME_1='2' # wait 2 minutes until power down
HDTUNE_32BIT_1='yes' # 32 BIT IO on: yes or no
HDTUNE_DMA_1='yes' # DMA ACCESS: yes or no
HDTUNE_READLA_1='yes' # Read-Lookahead: yes or no
PPP_NETMASK='255.255.255.0' # netmask
LPD_REMOTE_N='0' # how many remote printers are used
LPD_REMOTE_IP_1='192.168.6.99' # IP of 1st remote printer
LPD_REMOTE_QUEUENAME_1='pr1' # queue name of 1st remote printer
SAMBA_LPREMOTE_NET_1='' # allowed networks for LPD_REMOTE_IP_1, if empty all internal nets
SAMBA_CDROM_N='0' # crate shares for N CDROMs
SAMBA_CDROM_DEV_1='hdc' # name of the CDROM device eg. hdc
SAMBA_CDROM_NET_1='' # allowed networks for 1st CDROM, if empty all internal nets
VBOX_SPOOLPATH='/usr/local/data'# path of the spooldirectory on ext2-partition,
# see MOUNT_x_POINT, use only with VBOX_COMMON_SPACE='yes'
VBOX_COMMON_SPACE='yes'
ISDN_CIRC_1_USEPEERDNS='no' # use dns server of your provider: yes or no
ISDN_CIRC_2_USEPEERDNS='no' # use dns server of your provider: yes or no
ISDN_CIRC_3_USEPEERDNS='no' # use dns server of your provider: yes or no
PPPOE_USEPEERDNS='no' # use dns server of your provider: yes or no
Obsolete Variablen:
OPT_HDSLEEP='no' # power down HD after some time
SLEEP_N='1' # numder of drives to set sleep-mode
SLEEP_TIME_1='2' # wait 2 minutes until power down
SLEEP_DISK_1='hda' # drive to power down
VBOX_SPOOLDIR='' # directory on ext2-partition, use only with
# VBOX_COMMON_SPACE='yes'
OPT_SWAP='no' # use swap-Partition: yes or no
PART_SWAP='hda3' # partition, created by HD-Setup
Neue Variablen:
RAMSIZE='2048' # size of ramdisk for unzipped opt.tgz
MOUNT_OPT='ro' # mount opt device: ro, rw
PART_OPT='hda2' # location of opt-files? ram2 or disk-partition
UPDATE_MODE='full' # add, cfg, full, none, see documentation
OPT_MOUNT='no' # mount disks or cdroms: yes or no
MOUNT_N='1' # number of mounts
MOUNT_1_DEV='hda4' # example: 1st partition of first hard disk
MOUNT_1_POINT='/usr/local/data' # mount point, here: /hd
MOUNT_1_FS='ext2' # filesystem type: fat, vfat, or ext2
MOUNT_1_CHECK='yes' # check/repair filesystem if corrupted: yes, no
MOUNT_1_OPTION='rw' # additional options, see documentation!
OPT_HDINSTALL='no' # install on harddisk: yes or no
OPT_SWAP='no' # use swap-Partition: yes or no
PART_SWAP='hda3' # partition, created by HD-Setup
OPT_FDISK='no' # create partitions manually
OPT_HDSLEEP='no' # power down HD after some time
SLEEP_N='1' # numder of drives to set sleep-mode
SLEEP_TIME_1='2' # wait 2 minutes until power down
SLEEP_DISK_1='hda' # drive to power down
Obsolete Variablen:
keine
keine
Neue Variablen:
PPTP_DEBUG='no' # enable pppd debugging, 'yes' or 'no'
DNS_FORBIDDEN_N='0' # number of forbidden domains
DNS_FORBIDDEN_1='foo.bar' # 1st forbidden domain
DNS_FORBIDDEN_2='bar.foo' # 2nd forbidden domain
Neue Variablen:
HTTPD_USER_N='1' # Numbers of users for the HTTPD-server
HTTPD_USER_1='admin' # Name of the 1st user
HTTPD_PASS_1='fli4l' # Password of the 1st user
HTTPD_RIGHTS_1='all' # Rights of the 1st user
LCD_TYPE_ONLINE_N='3' # no. of data types to show if online
LCD_TYPE_ONLINE_1=' 8 0 0' # dsl status
LCD_TYPE_ONLINE_2='39 7 0 :' # Text
LCD_TYPE_ONLINE_3='31 9 0' # dsl online time
LCD_TYPE_OFFLINE_N='2' # no. of data types to show if offline
LCD_TYPE_OFFLINE_1=' 0 0 0' # local date
LCD_TYPE_OFFLINE_2=' 2 12 0' # local time
LCD_VAR_TEXT_1='Text1' # Default-Text 1 -> /etc/lcd_text1.txt
LCD_VAR_TEXT_2='Text2' # Default-Text 2 -> /etc/lcd_text2.txt
LCD_VAR_TEXT_3='Text3' # Default-Text 3 -> /etc/lcd_text3.txt
LCD_VAR_TEXT_4='Text4' # Default-Text 4 -> /etc/lcd_text4.txt
Obsolete Variablen:
HTTPD_USER
HTTPD_PASS
keine
Neue Variablen:
OPT_MOUNT='no' # mount disks or cdroms: yes or no
MOUNT_N='1' # number of mounts
MOUNT_1_DEV='/dev/hda1' # example: 1st partition of first hard disk
MOUNT_1_POINT='/hd' # mount point, here: /hd
MOUNT_1_FS='vfat' # filesystem type: fat, vfat, or ext2
MOUNT_1_OPTION='ro' # additional options, see documentation!
OPT_SCSI='no' # install SCSI drivers: yes or no
SCSI_DRV_N='1' # number of SCSI drivers, '2' means: with cdrom
SCSI_DRV_1='aha1542' # Adaptec AHA154x Controller
SCSI_DRV_1_OPTION='' # enter driver option here, optional!
IP_DEFAULT_GATEWAY='' # normally not used, read documentation!
LCD_OPTION='' # set 'a_type=1', if you have a HD66712 chip
Neue Variablen:
NMBD_WINSCLIENT='no' # act as an WINS-Client: yes or no
NMBD_EXTWINSIP='' # IP address of the external WINS-Server
NMBD_WINSPROXY='no' # act as an WINS-Proxy : yes or no
Obsolete Variablen:
REV_NET
Geänderte Variablen:
FORWARD_DENY_PORT_x # zusätlicher Parameter DENY oder REJECT
FIREWALL_DENY_PORT_x # zusätlicher Parameter DENY oder REJECT
Neue Variablen:
IMOND_ADMIN_PASS='' # imond-admin-password, may be empty
IMOND_BEEP='no' # beep if connection going up/down
ISDN_CIRC_x_BANDWIDTH='6144 30' # if bundling=yes: opt. bandwidth on demand
HTTPD_PORT='80' # http port, see also FIREWALL_DENY_PORT_x !
HTTPD_USER='admin' # user for the webserver
HTTPD_PASS='fli4l' # password for the webserver
FTPD_PORT='21' # ftp port, see also FIREWALL_DENY_PORT_x !
LPD_PORT_N='1' # how many ports for printing are used
Geänderte Variablen:
LCD_*
LPD_PORT_1='0x378' # io-adress for printer on 1st port: 0x3bc,0x378 or 0x278
VBOX_USERS_N='1' # number of users
Umbenannte Konfigurationsvariablen:
Alt: Neu:
----------------------------------------------------------------------------
VBOX_N_USERS='1' VBOX_USERS_N='1
Neue Variablen:
IP_ROUTE_N='0' # number of additional routes
IP_ROUTE_1='192.168.7.0 255.255.255.0 192.168.6.99' # network netmask gateway
DENY_FORWARD_PORT_N='1' # number of ports to deny forwarding (in & out)
DENY_FORWARD_PORT_1='137:139' # deny forwarding of netbios ports
FIREWALL_DENY_ICMP='no' # deny icmp (e.g. ping) from outside: yes or no
OPT_KLOGD='no' # start klogd: yes or no
OPT_LPD='no' # install lpd as printer server: yes or no
OPT_SAMBA='no' # install samba as printer server: yes or no
ISDN_CIRC_1_COMPRESSION='no' # compress headers if ppp: 'yes' or 'no'
PPPOE_DEBUG='yes' # enable pppd debugging, 'yes' or 'no'
OPT_PROXY='no' # proxy junkbuster: yes or no
PROXY_ACCESS='192.168.6.0/24' # proxy: permit access from lans x.x.x.x/nn ...
PROXY_PORT='8000' # proxy: listen port, see also FW_PORT_x
PROXY_FORWARD='' # proxy: optional forward-host:forward-port
Obsolete Variablen:
OPT_PRINT
IP_ETH_1_ROUTE
IP_ETH_1_GATEWAY
Umbenannte Konfigurationsvariablen:
Alt: Neu:
----------------------------------------------------------------------------
ETH_N_DRV ETH_DRV_N
MASQ_N_MODULES MASQ_MODULE_N
FW_N_PORTS FIREWALL_PORT_N
FW_PORT_x FIREWALL_PORT_x
DENY_N_HOSTS DENY_HOST_N
TELMOND_N_MSN TELMOND_MSN_N
TELMOND_N_CMD TELMOND_CMD_N
LCD_N_TYPES LCD_TYPE_N
CIRCUITS_N ISDN_CIRCUITS_N
CIRC_x_NAME ISDN_CIRC_x_NAME
CIRC_x_TYPE ISDN_CIRC_x_TYPE
CIRC_x_BUNDLING ISDN_CIRC_x_BUNDLING
CIRC_x_LOCAL ISDN_CIRC_x_LOCAL
CIRC_x_REMOTE ISDN_CIRC_x_REMOTE
CIRC_x_NETMASK ISDN_CIRC_x_NETMASK
CIRC_x_MTU ISDN_CIRC_x_MTU
CIRC_x_MRU ISDN_CIRC_x_MRU
CIRC_x_IPX_NETWORK ISDN_CIRC_x_IPX_NETWORK
CIRC_x_IPX_NODE ISDN_CIRC_x_IPX_NODE
CIRC_x_REMOTENAME ISDN_CIRC_x_REMOTENAME
CIRC_x_USER ISDN_CIRC_x_USER
CIRC_x_PASS ISDN_CIRC_x_PASS
CIRC_x_ROUTE ISDN_CIRC_x_ROUTE
CIRC_x_DIALOUT ISDN_CIRC_x_DIALOUT
CIRC_x_DIALIN ISDN_CIRC_x_DIALIN
CIRC_x_CALLBACK ISDN_CIRC_x_CALLBACK
CIRC_x_CBDELAY ISDN_CIRC_x_CBDELAY
CIRC_x_EAZ ISDN_CIRC_x_EAZ
CIRC_x_DEBUG ISDN_CIRC_x_DEBUG
CIRC_x_AUTH ISDN_CIRC_x_AUTH
CIRC_x_HUP_TIMEOUT ISDN_CIRC_x_HUP_TIMEOUT
CIRC_x_CHARGEINT ISDN_CIRC_x_CHARGEINT
CIRC_x_TIMES ISDN_CIRC_x_TIMES
START_TELMOND OPT_TELMOND
PRINT_PORT LPD_PORT
PRINT_RAM LPD_RAM
PRINT_WORKGROUP SAMBA_WORKGROUP
PRINT_ADMINIP SAMBA_ADMINIP
PRINT_LPNET SAMBA_LPNET
PRINT_TIMESERVER SAMBA_TIMESERVER
Obsolete Variablen:
PPPOE_CIRCUIT
Neue Variablen:
MASQ_MODULE_9='pptp' # masquerading module: pptp
MASQ_MODULE_10='ipsec' # masquerading module: ipsec
TELMOND_LOGDIR='/var/log' # telmond: log-directory, e.g. /var/log
OPT_WGET='yes' # install wget, see wget howto on www.fli4l.de
LCD_N_TYPES='6' # number of data types to show, see docum.
LCD_TYPE_1='0' # local date
LCD_POS_1='0,0' # 1st line, left
...
Umbenannte Konfigurationsvariablen:
Alt Neu
----------------------------------------
ETH_N_DRV ETH_N_DRV
MASQ_N_MODULES MASQ_N_MODULES
DENY_HOSTS_N DENY_HOSTS_N
TELMOND_N_MSN TELMOND_N_MSN
TELMOND_N_CMD TELMOND_N_CMD
ETH_N ETH_N
HOSTS_N HOSTS_N
DNS_N DNS_N
CIRCUITS_N CIRCUITS_N
Obsolete Variablen:
OPT_IDE - IDE-Festplatten-Treiber nun fest im Kernel
OPT_REBOOT - entfallen
FW_PORTS - s. FW_N_PORTS
Neue Variablen:
MOUNT_BOOT='rw' # mount boot device (floppy): ro, rw, no
FW_N_PORTS='6' # number of ports denied by firewall
FW_PORT_x
IMOND_PORT='5000' # imond: TCP-Port
IMOND_LED='' # imond: tty for led: com1 or com2 or empty
IMOND_LOGDIR='/var/log' # imond: log-directory, e.g. /var/log
TELMOND_PORT='5001' # telmond: TCP-Port
PPPOE_CIRCUIT='no' # use pppoe as circuit
PPPOE_NAME='DSL' # circuit name, don't write spaces
PPPOE_CHARGEINT='60' # value of charge interval (in seconds)
PPPOE_TIMES='Mo-Su:00-24:0.0:Y' # times/charges when to enable this circuit
OPT_PPTP='no' # use PPP over ethernet: yes or no
PPTP_ETH='eth0' # ethernet card connected to ADSL modem
PPTP_USER='anonymer' # username
PPTP_PASS='surfer' # password
PPTP_HUP_TIMEOUT='600' # idle time after which to hangup
PPTP_MODEM_TYPE='bbaa' # 2 different types in Austria: bbaa or bcaa
OPT_HTTP='yes' # install mini web server: yes or no
TIME_ZONE='MET' # timezone: MET or GMT
TIME_ACCESS_AT_BOOT_TIME='yes' # access at boot time: yes or no
TIME_CIRCUITS='1 2 3' # circuit indices when to activate time sync
OPT_PCMCIA='no' # pcmcia cards used: yes or no
PCMCIA_PCIC='i82365' # pcmcia socket driver: 'i82365' or 'tcic'
PCMCIA_PCIC_OPTS='' # option for socket driver, usually empty
PCMCIA_CORE_OPTS='' # option for pcmcia core driver, usually empty
PCMCIA_CARDMGR_OPTS='' # option for pcmcia card manager, usually empty
Obsolete Variablen:
CIRC_x_PAP, stattdessen CIRC_x_AUTH
Neue Variablen:
ISDN_DEBUG_LEVEL='31' # debug level (hisax driver)
ISDN_VERBOSE_LEVEL='2' # verbose level
CIRC_1_MTU='1024' # maximum transmission unit
CIRC_1_MRU='1524' # maximum receive unit
CIRC_1_CBDELAY='3' # callback delay, only used for callbacks
CIRC_1_AUTH='' # require the peer to authenticate itself
ROUTE_NETWORK='' # optional: route from/to network, no masq
TELMOND_N_CMD='0' # number of commands to be executed if call-in
TELMOND_CMD_1='123 * sleep 5; imonc dial' # example: dial out via default circuit
PRINT_WORKGROUP='arbeitsgruppe' # workgroup name of windows-clients
PRINT_ADMINIP='192.168.0.2' # ip address of smb-client (mount fli4l rootfs)
OPT_NMBD='no' # install nmbd as SMB Nameserver
DHCP_LS_TIME_DYN='3600' # default time for dynamic leases: 1 hour
DHCP_MAX_LS_TIME_DYN='7200' # max time for dynamic leases: 2 hours
DHCP_LS_TIME_FIX='86400' # default time for fix leases: 1 day
DHCP_MAX_LS_TIME_FIX='604800' # max time for fix leases: 1 week
OPT_IDE='no' # install IDE drivers: yes or no
OPT_CDROM='no' # install CDROM drivers: yes or no
OPT_REBOOT='no' # use orig reboot pgm instead of busysbox
Obsolete Variablen:
ADD_DAYS: siehe unten: OPT_Y2K, OPT_DAYS
Neue Variablen:
IP_ETH_1_NAME='' # optional: other device name than ethX
DNS_FORWARDERS='' # if set, install "named" instead of "dnscache"
DNS_VERBOSE='no' # yet only used if named
DENY_HOSTS_N='2' # number of forbidden hosts
DENY_HOST_1='192.168.6.5' # optional: 1st forbidden host
DENY_HOST_2='192.168.6.6' # optional: 2nd forbidden host
OPT_Y2K='no' # y2k correction: yes or no
Y2K_DAYS='' # correct Y2K-Bug on old hardware: add x days
SYSLOGD_DEST='/dev/console' # destination of syslog messages
OPT_DHCP='no' # install DHCP server: yes or no
DHCP_RANGE_1='192.168.6.2 192.168.6.100' # range of n'th ethnet, see IP_ETH_N!
Neue Variablen:
TELMOND_N_MSN='0' # number of msn->ip mapping entries
TELMOND_MSN_1='123 192.168.6.2' # example: map MSN 123 to client 192.168.6.2
Obsolete Variablen:
START_NAMED
VERBOSE_NAMED
DNS_SERVER
START_SYSLOGD
Neue Variablen:
START_DNS='yes' # start dns server: yes or no
DNS_N='0' # number of special dns servers, normally 0
DNS_x='...' # n'th special dns server
OPT_SYSLOGD='no' # start syslogd: yes or no
FW_PORTS='' # ports 5000,5001,21,23,53,139,515 denied
PASSWORD='fli4l' # password for telnetd, ftpd, and samba
IMOND_LOG='no' # imond: log /var/log/imond.log: yes or no
TELMOND_LOG='no' # telmond: log /var/log/telmond.log: yes or no
OPT_PNP='no' # install isapnp tools: yes or no
OPT_RESCUE='no' # install telnetd, ftpd and e2fsck
OPT_TELNETD='no' # install telnetd: yes or no
OPT_FTPD='no' # install ftpd: yes or no
OPT_LCD='no' # install lcd driver and tools: yes or no
LCD_COLS='20' # number of lcd columns (16,20,32,40) dflt: 20
LCD_LINES='4' # number of lcd lines (1,2,4) dflt: 4
LCD_ADDRESS='0x0378' # IO address of used lpt port
LCD_TIME_LONG='' # long delay time (empty = default: 100)
LCD_TIME_SHORT='' # short delay time (empty = default: 40)
LCD_START_ISDN_RATE='yes' # start isdn rating display on lcd: yes or no
OPT_PPP='no' # install serial ppp package
PPP_DEV='com1' # serial ppp: COM port - empty, com1 or com2
PPP_SPEED='38400' # serial ppp: COM port speed
PPP_IPADDR='192.168.4.1' # serial ppp: IP address of fli4l router (COMx)
PPP_PEER='192.168.4.2' # serial ppp: IP address of peer (pointopoint)
PPP_NETWORK='192.168.4.0' # serial ppp: network
OPT_PPPOE='no' # use PPP over ethernet: yes or no
PPPOE_ETH='eth0' # ethernet card connected to ADSL modem
PPPOE_USER='anonymer' # username
PPPOE_PASS='surfer' # password
PPPOE_HUP_TIMEOUT='600' # idle time after which to hangup
PPPOE_SYNCHRONOUS='no' # synchronous ppp: yes or no
OPT_IMODEM='no' # install isdn modem emulator: yes or no
IMODEM_MSN='81330' # isdn modem emulator: your msn
IMODEM_SERIAL='com1' # isdn modem emulator: COM port
IMODEM_SPEED='115200' # isdn modem emulator: COM speed
OPT_PRINT='no' # install printer server: yes or no
PRINT_PORT='lpt1' # printer server port: lpt1, lpt2, or lpt3
PRINT_RAM='4096' # use 4 MB RAM (= 4096 KB) for printer queue
OPT_PORTFW='no' # install port forwarding tools/modules
OPT_TIME='no' # install time zone informations: yes or no
TIME_SERVER='ntps1-1.uni-erlangen.de' # name of time server, may be empty
DIALMODE='auto' # standard dialmode: 'auto', 'manual', or 'off'